ASTM A513 PDF

Learn about ASTM A steel mechanical tubing and Atlas Tube’s manufacturing capabilities regarding this product for OEM applications. CALIFORNIA. Arrow Route. Rancho Cucamonga, CA WWW. ASTM A TUBING SPECIFICATIONS. TOLERANCES. ASTM A/AM: Standard Specification for Electric-Resistance-Welded Carbon and Alloy Steel Mechanical Tubing.

Author: Bram Zolobar
Country: Portugal
Language: English (Spanish)
Genre: Automotive
Published (Last): 8 April 2008
Pages: 227
PDF File Size: 19.94 Mb
ePub File Size: 12.92 Mb
ISBN: 368-3-35489-521-6
Downloads: 18237
Price: Free* [*Free Regsitration Required]
Uploader: Febei

A — 07 Standard Speci?

A number in parentheses indicates the year of last reapproval. A superscript epsilon e indicates an editorial change since the last revision or reapproval. This standard has been approved for use by agencies of the Department of Defense. Current edition approved March 1, Originally approved in Last previous edition approved in as A — 06b. The heat analysis shall conform to the requirements speci?

A513 Square Carbon Steel Tube

When requested in the order or contract, a report of such analysis shall be furnished to the purchaser. The number and source of samples for such product analysis shall be based on the individual heat or lot identity of one of the following forms of material: The composition thus determined shall correspond to the requirements of Tables Both retests for the elements in question shall meet the requirements of the speci? Permissible Variations in Dimensions for Round Tubing 8.

Permissible variations in outside diameter for tubing that has been sinkdrawn for closer tolerance on outside diameter are shown in Table 5. Permissible variations in wall thickness for tubing made from hot-rolled steel are shown in Table 6. Permissible variation in outside and inside diameter for tubing made from hot-rolled steel that has been Drawn Over a Mandrel DOM for closer tolerances are shown in Table 5 with wall tolerances shown in Table 7.

Materials and Manufacture 4. If secondary melting is employed, the heat shall be de? When steel of different grades is sequentially strand cast, identi? The producer shall remove the transition material by an established procedure that positively separates the grades. If no grade is speci? Analyses of steels other than those listed are available.

To determine their availability, the purchaser should contact the producer. Product analysis, except for rimmed or capped steel, is to be in accordance with usual practice as xstm in Table 3.

Aa513 Where the ellipsis Outside diameter 3 tolerances for cold-rolled steel tubing, sink drawn and DOM, are shown in Table 5. Permissible variations in wall thickness for round tubing, DOM for closer tolerances, are shown in Table 7. Side leg of square to be equal to tube diameter zstm minimum length of 1 in. Outside diameter burr to be removed for measurement.

  BANISHING BUREAUCRACY-DAVID OSBORNE AND PETER PLASTRIK PDF

For lengths under 1 ft the straightness tolerance shall be agreed upon between the aztm and producer. A from the ends of the tubes. Wall Thickness Outside Diameter Range, in. Flash-In-Tubing is produced only to outside diameter tolerances and wall thickness tolerances and the inside diameter welding? C Flash Controlled to 0. D No Flash tubing is further processed by DOM for closer tolerances, produced to outside diameter and wall, inside diameter and wall, or outside diameter and inside diameter, with no dimensional indication astmm inside diameter?

E Flash Controlled to 0. F Birmingham Wire Gage. D Round Tubing Outside Diameter, in. The outside corners may be slightly? The radii of corners shall be as given in Table C Tubing produced to outside diameter and wall thickness, or inside diameter and wall thickness, or outside s513 and inside diameter, by DOM to obtain tolerances closer than those shown in Tables 4 aastm 8 and no dimensional indication of inside diameter? The squareness of sides is commonly determined by one of the following methods.

The twist in square and rectangular tubing may be measured by holding one end of the tubing on a surface plate and noting the height of either corner of the opposite end of same side above the surface plate. Twist may also be measured by the use of a beveled protractor equipped with a level, and noting the angular deviation on opposite ends, or at any point throughout the length.

Round Tubing Wall thickness 34 Outside Diameter, in. Wall Thickness Tolerances, in. Round Tubing Outside Diameter, in. A Wall Thickness in. Types and Conditions Type Ast, 1a 1b 2 3 4 5 6? C Where the ellipsis Manufacturing practices limit the size range and section available from the various producers.

These special sections may be made through turkshead rolls or through a die with or without use of a mandrel. Since the sections are special, dies and other tools are not held available. Therefore, when inquiring for shapes other than square and rectangular, it is essential to give full details as to dimensions and? Workmanship, Finish, and Appearance When an oxide-free surface is speci? Tubing furnished to this speci? This condition is available in Types 1a, 1b, 2, 3, and 4.

This condition is available in Types 1a, 1b, and 2 over 11? Any remaining inside diameter? A Flash Controlled to 0.

Flash-In-Tubing is produced to outside diameter tolerances and wall thickness tolerances only, and the height of the inside welding? D Flash Controlled to 0. E Birmingham Wire Gage. G Where the ellipsis Should the order specify that tubing be shipped without rust retarding oil, the? A Wall Thickness 38?

  FURSTENAU FLUTE PDF

C Where the ellipsis appears in this table, the tolerance is not addressed. For each additional 10 ft or fraction thereof over 24 ft, an additional allowance should be made of plus or minus 1? Tubes having two parallel sides are also measured in the center of the? This tolerance applies astj the speci? Largest Nominal Outside Dimension, in. The purchaser may specify in the order a speci?

Tubing heavier than 16 gage will normally be shipped loose, bundled, or in secured lifts.

ASTM A Mechanical tubing VS ASTM A Mechanical tubing|SHEW-E

Special packaging requiring extra operations other than those normally used by a producer must be speci? If the order speci?

Such requirements shall be considered under the supplementary or basis of purchase provisions of this speci? Product and Package Marking Bar qstm is acceptable as a supplementary identi? B Radius Tolerances, in. The purchaser and producer may negotiate special radii. C Asgm radius tolerances apply to grades of steel covered in Table 1. The purchaser and producer may negotiate tolerances on other grades of steel.

These requirements shall not be considered, unless speci? Mechanical tests shall be performed in accordance with the applicable portions of Test Methods and De? Tubes for Cylinders S1.

ASTM A513 Gr 1050 Tube, Size: 1/2 Inch, 3/4 Inch, 1 Inch, 2 Inch, 3 Inch

Cleanup by Centerless Aa513 S2. Cleanup by Machining S3. Special Smooth Inside Surface S4. Hardness and Tensile Requirements S5. For grades of round tubing not shown in Table S5. If the results of the mechanical tests do not conform to the requirements shown in the table, retests shall be made on additional tubes double the original number selected, each of which shall conform to the speci?

NOTE S1—A lot shall consist of all tubes, before cutting to length, of the same size and wall thickness which are produced from the same heat of steel and, when heat treated, subjected to the asym

Destructive Weld Tests S6. B,C Outside Diameter, in. B Up to and incl 11?

Except as allowed in S6. No cracks or breaks in the base metal shall occur until the distance between the plates is less than one third of the original outside diameter of the tubing, but in no case less than?