BENTEL J524F PDF

be equipped with a BENTEL BA ( V – 4 A) Linear power supply or BENTEL SECURITY srl reserves the right to change the technical features of this . bentel jf. hello i have a fire security system bentel jf and i cant find the instaler manual or usser manual please can anibody help my thx. Bentel JF tulekahju signakeskus в категории: Рабочее оборудование, строительство, Другие машины и оборудование (ID номер.

Author: Vogor Kagakinos
Country: Kenya
Language: English (Spanish)
Genre: Health and Food
Published (Last): 9 February 2014
Pages: 283
PDF File Size: 6.11 Mb
ePub File Size: 5.66 Mb
ISBN: 321-9-57853-922-6
Downloads: 48723
Price: Free* [*Free Regsitration Required]
Uploader: Grogore

DSC section locked out?

Bentel j424 manual pdf

I have a fault 5 on zone 1 that I can’t seem to clear. I recently added an extra keypad and reassigned all 3 keypads to 11,12 and I wanted to make sure the keypad zones are null to eliminate the possibility of zone 1 being associated with a keypad, but when I try to enter section I get the long error beep. Is this a hardware issue, or have I somehow disabled this function? Zone 1 is supposed to be a smoke detector but I have since disconnected the input wire and made it null 00but the fault will not clear.

Another issue is that I have set the front door for entry delay but it sets the alarm off immediately. I have re-entered the 30 second entry time, but still have problems.

Thanks in advance for any help! Find all posts by loach1. Exactly what keystrokes did you enter to make the changes you described?

Bentel J524-F tulekahju signakeskus

It’s really easy to be one segment off and not realize it. Find all posts by MrRonFL. Ron, thanks so much for responding – I have been reading a lot of your advice lately trying to figure this out, and had been hoping that you would come to my aid! Glass break To set the zones I entered: Currently I have 00 for zone 1 in an attempt to clear the fault. Any idea why I cannot enter section ? Hmmm, if this was an ADT branded PC, they often have such specialty programming locations disabled from the programming.

Also, the very oldest versions of the PC did not have the keypad zone feature. What is the version number on the label on your main chip in the center of the motherboard? It is a CPI unit, which seems to be standard everything has always worked for me up until now anyway. The largest chip has the following: R, L8 on it. Below the PC number is Rev 4A at least it looks like an ‘A’ but a solder pad obscures most of it.

  KIMYASAL TANKER ILEMLERI PDF

I’m considering a reset as a next step since there isn’t much to do to get it back and running and I might clear whatever mistake I made. OK, I decided to go for it and did a software reset. I still have a fault 5 showing zone 1 trouble, have toggled the EOL and NC option in sectionno change. I have a number ‘1’ on the panel at all times, but the system clock has been set. Do I need to change something else?

Bentel Security | User Manuals

Master code has been changed too. Otherwise, simply jumper it closed. If the zone benhel, then it’s a field wiring issue. If it doesn’t, then you may have a failed zone input.

I will try the jumper trick in a second and beentel back. A bit more testing bbentel the bell unwired shows that everything behaves like it should, BUT The continuous beep from the keypad is correct, with a solid number on the LED for the zone.

If I violate an instant zone such as the motion detector there is no beep from the keypad, just the zone number flashing and I would guess the bell would be sounding too like it should. Any ideas on why the bell goes off although during the entry delay period? The jumper for zone 1 resulted in the ‘Fire’ LED coming on, and there was still a fault on zone 1.

I j524t know what this means I’m a bit worried that I have assigned zone 1 to a keypad but since I can’t enter section I can’t ’00’ the keypad zones out.

Is there a reset j254f the keypads? This time I started out by calling zone 1 ’00’ rather than bnetel and it didn’t give me a fault. The only remaining issue was a battery fault so I checked the voltage and it was I had another battery with Benfel zone 1, but I have a bunch of smoke alarms anyway and do not have monitoring. I tried the zone 4 door after arming and it behaved the same way – continuous beep at the keypads and the bell went off immediately.

Soon my ‘monitoring’ neighbor is going to give up on betel What could be causing this lack of entry delay? I would go into installer program and press to reset the module list first. After 1 minute do to confirm proper modules. I had the benetl thing happen to me a few days ago with a fire zone. I had programmed a zone for fire that wasn’t, it went into trouble and wouldn’t clear by reprogramming the zone. Apparently the panel needs to see fire zones clear normally before the trouble will clear.

Reprogram backto fire, let it go into trouble, put the resistor across the zone then reset the keypad. Or default the panel programming and start over. Find all posts by AllTrack. A fully charged battery is supposed to have about It’s also the voltage that the charger puts out. I think you may have swapped a good battery for a failing one. The keystrokes you are writing out are the correct ones, but I don’t think that’s what you are actually entering.

  ECKHART TOLLE EL SILENCIO HABLA DESCARGAR PDF

It’s really easy to get one segment off with one of these things. View your zone types to make sure that they actually have the right settings. I’m not sure why you are unable to access location This all feels like you are a little off in your programming locations, somehow.

Well, I had a bit of time to play with it again so I re-entered the zone definitions like this: I changed the 01’s to 02’s to see if it helped to use a different timer. I also changed the basement door to instant I also changed the times: I am leaning towards a dud board since I have performed hardware and software resets. Or could it be that my new keypad is not fully compatible with the system?

It seems to be working as it should though an section 20 was accessible k524f I initially installed the keypad. I’m starting to lean that way myself. Turn off light 6 in location Test your entrance delay.

Very simple really – I was not aware of the 4 second ‘fault’ period after the exit delay. I had been opening the door immediately after arming because I had a house full of kids nentel didn’t want them to set off a motion sensor before I had a chance to check the door.

Thanks for all your help! Betnel sounded like you were familier with the system, so it never occurred fo me the check that you had let the exit j5224f time out Find all posts by Microlab.

Benyel may not post new threads. BB code is On.

Bentel j manual pdf

Newsletter Sign-Up Signup Email address. Tub pump air tube came off. Need replacement screw for fireplace gas valve. What do you set your thermostat j524ff Posted In General Chats and Discussions. Noisy Boiler – Air or something else? Aprilaire – Basic Solenoid Question. Trying to hook up tire changer motor to switch.

What is this old floor.

Gas water heater too hot.