This manual provides technical information necessary for servicing the FTR Transceiver. Servicing this equipment requires expertise in handling. Compact FTR Mini-Manual. Size, x8 inches. Twelve high-quality laminated pages, loaded with detailed instructions. An ideal short-form instruction . Yaesu FTR Operating Manual Expanded Edition (courtesy of W5JCK). Page 2 of Table of Contents. About this Manual.
|Published (Last):||2 February 2018|
|PDF File Size:||1.12 Mb|
|ePub File Size:||16.19 Mb|
|Price:||Free* [*Free Regsitration Required]|
Yaesu FT-8900R Operating Manual
Menu h 42 VFO. Notes are presented ft-8900g below: Notes typically contain extra information designed to clarify the information presented in a topic. Press this key momentarily to enter the mode. Busy Channel or Squelch Off: Key Function Mode is set to: Press or hold in either of these buttons to tune or scan up or down the operating frequency or through the memory channels on the band. In many ways, these buttons emulate the Main function of the rotary knob.
Press the button to switch operation to the on the band.
The scanning direction will be reversed. To revert to scanning toward a higher frequency once more, rotate the knob one click clockwise. DIAL Press the key again to cancel scanning. Press the momentarily to save the new setting and exit to normal SET key operation.
To unlock the panel switches and knobs, select in step 3 above. Audio Mute level of the band whenever you receive a signal on the band or you Receive Only Main transmit on the band during operation. To configure for the narrower bandwidth, use the following procedure: Press the momentarily to enter the mode. Rotate the knob to select Menu 43 WID. Tune to MHz on the band and repeat steps 3 through 5 to store Tuning and scanning engaged by pressing the momentarily will now be limited within the just-programmed range.
Enter the transmit and receive frequencies separately, as shown in Store Independent Transmit Frequencies on page Press the knob momentarily to enable adjustment of the frequency.
CTCSS station or stations, you can command the radio to listen to the incoming signal and scan in search of the tone being used. Occasionally, signal inversion can result in the complement of a code to mmanual sent or received.
This prevents the receiver squelch from opening with enabled, as the decoded bit sequence would not match that selected for the operation. Regular Memory Channels channels see page 32numbered through Standard Memory channels see page 36providing storage and quick recall of one prime The icon will disappear.
HOME You may repeat this process on the other operating bands. To recall the channel, just press the key while operating either in the HOME mode. To return to normal operation, repeat the above steps.
Set up the transceiver according to the desired configuration. Press and hold in a key through for 2 seconds. The current Hyper Memory configuration will ft-8900r stored in this channel. Hyper Memory keys for two seconds. HOME check the for activity. Priority Memory Channel 4. Press and hold in the key to disable the mode. Preferential Only channels flagged as Preferential will be scanned. Menu 35 Preferential Memory on page 47 for details. Ft-8900g the key momentarily to initiate Standard Memory Scanning 3.
To cancel thepress the momentarily. Rotate the knob to select DIAL 3. Only the Preferential Memory Scanning channels which have the icon displayed will be scanned.
To cancel thepress the key momentarily. The available options are: DIAL to confirm the callsign. Press the knob momentarily to save the setting and exit to normal DIAL operation. Press the knob momentarily to save the new setting. To disable the feature, press the left knob again.
Yaesu FT-8900R Mini-Manual
Press the knob again to activate the mode. Turn both transceivers off, then remove the Cloning Cable Channel and operating data for both radios are now identical. They both may be turned on now for normal operation.
Clears all memories and other settings to factory defaults. Press the momentarily to complete the procedure. AM Selects the receiving mode. Automatic Repeater Shifts Values: Depends on the band of operation.
VFO frequency will jump to the low band edge of the next band or vice versa. Stores your callsign into the. Up to six characters may be stored. CW Identifier on page 51 for details. Internet Connection Feature — — Values: Program the Microphone Buttons Values: Scanning will halt on a signal it encounters. Two seconds after the carrier has dropped because the other station s ceased transmission, scanning will resume. Cross-Band Repeater on page 57 for details.
Operate as a Cross-Band Repeater Values: Page of 77 Go. Table of Contents Add to my manuals Add. Page 4 Menu h 42 VFO. About This Manual Notes are presented as below: Page 9 Press this key momentarily to enter the mode. Page 12 Press or hold in either of these buttons to tune or scan up or down the operating frequency or through the memory channels on the band.
Common Tasks Press the button to switch operation to the on the band. Change The Frequency The scanning direction will be reversed. Set The Display Brightness Audio Mute level of the band whenever you receive a signal on the band or you Receive Only Main transmit on the band ff-8900r operation.
Yaesu FTR Mini-Manual
Activate Automatic Power Off To configure for the narrower bandwidth, use the following procedure: Operate Through Repeatersyou may set the direction of the repeater shift manually. Tone Search Scanning CTCSS station or stations, you can command the radio to listen to the incoming signal and scan in search of the tone being used. Dcs Code Inversion Recall A Stored Memoryalthough the original memory contents will remain intact on the previously-stored channel. Activate Memory Only Mode 3.
Store A Hyper Memory 1. Standard Memory Scanif necessary. Internet Connection Feature Repeat step c. Menu 5 Beep Stores your callsign into the. Menu 9 Dimmer Function: Menu H 12 Dsp. Menu H 26 Pkt.
Menu 29 Pg P2 21 for details. Menu B 33 Rpt. Menu B 35 Scan M Menu 38 Spcont ENC. This manual also for: Comments to this Manuals Your Name. Enter text from picture: By pressing ‘print’ button you will print only current page. To print the manual completely, please, download it. Don’t show me this message again.